Water Heater Anode Rod Replacement Port Charlotte FL
Stop tank corrosion before it turns into a leak
Water heater anode rod replacement Port Charlotte FL homeowners call us for is the cheapest way to add years to a tank that is still structurally sound. If your water heater is past the five-year mark, that magnesium or aluminum rod inside is likely half eaten. We pull it, inspect the tank lining, and install a fresh rod the same visit. One appointment, usually under two hours.
What Water Heater Anode Rod Replacement Port Charlotte FL Involves
Water heater anode rod replacement Port Charlotte FL is a maintenance procedure that swaps the sacrificial metal rod inside your tank before corrosion reaches the steel shell. That rod, usually magnesium or aluminum, is designed to rust so your tank does not. Once it is consumed, the tank lining becomes the anode and starts failing from the inside. We drain the tank, break the rod loose with a pipe wrench, pull it through the top port, and thread in a new one sealed with fresh Teflon tape.
Port Charlotte water sits high in dissolved minerals, and the heat inside a tank accelerates the reaction. Most rods here are spent by year five or six, well before the tank itself looks bad. If you have been searching for water heater anode rod replacement in Port Charlotte FL near me because your hot water smells like sulfur or your tank is making popping sounds, that is sediment and a depleted rod talking. Catching it now is a $200-$400 job instead of a $1,400 tank swap.
Why Port Charlotte Homeowners Replace Anode Rods
A fresh anode rod is the single cheapest insurance policy on a water heater. These are the four outcomes our Port Charlotte customers notice most.
Extends Tank Life
A healthy anode rod routinely adds three to five years to a tank that would otherwise rust through. On a Rheem or A.O. Smith unit that is only six years old, that is real money saved. We check rod condition on every maintenance visit so you replace it on schedule, not after the tank starts weeping.
Kills Rotten Egg Smell
That sulfur smell in your hot water is bacteria reacting with a depleted magnesium rod. Swapping to an aluminum or zinc rod and flushing the tank clears it in one visit. Most Port Charlotte customers notice the difference the same evening.
Prevents Rusty Hot Water
Brown or rusty hot water usually means the tank lining has started to corrode. Replacing the rod early stops that process. If the water clears after a flush and rod swap, you have saved the tank. If it stays rusty, we tell you straight that replacement is the better call.
Protects Your Warranty
Bradford White, State Water Heaters, and most major brands require anode maintenance to keep the tank warranty valid. We document the rod condition and the replacement so you have a record if you ever file a claim. It takes ten minutes and it protects a six-year warranty.
How Our Anode Rod Replacement Process Works
Every job follows the same five steps. You get a call or text when we are on the way, a clear price before we start, and a dry floor when we leave.
Phone Assessment
You call (941) 466-8418 and describe the tank: age, brand, gas or electric, and what you are seeing. We ask about water smell, popping sounds, and whether the T&P valve has been weeping. That conversation usually tells us whether you need a rod swap or a full replacement, and we quote a range on the spot.
On-Site Tank Check
We shut off the gas or breaker, close the cold inlet, and connect a hose to the drain valve. Before anything comes apart, we test the T&P valve with a tester and check the thermostat reading. If the tank shell is already compromised, we stop and talk replacement instead of selling you a rod that will not help.
Drain and Rod Removal
We drain roughly five gallons into a bucket or floor drain, then break the anode rod loose with a pipe wrench. On older tanks the rod can be seized, so we use a cheater bar and steady pressure. A tube cutter and press tool come out if the rod is a segmented type that has to come out in pieces.
New Rod and Inspection
We install a fresh magnesium, aluminum, or powered anode rod, wrapped with Teflon tape and torqued to spec. While the tank is open we check the dip tube, the heating element or burner assembly, and the T&P valve. If the expansion tank is waterlogged, we flag it before it becomes a separate problem.
Refill, Test, Cleanup
We refill the tank, purge the air from every hot tap, and restore power or gas. The burner or element comes on and we watch the temperature climb to setpoint. We check for weeping at the rod port, wipe down the tank, and walk you through what we found. Total time is usually 90 minutes to two hours.
Local Experience With Every Major Tank Brand
Our technicians work on residential water heaters every day across Charlotte County, from six-year-old builder-grade tanks to twenty-year-old units still running strong. We hold a Florida Plumbing License and pull a Charlotte County Permit when a job requires one. We install and service Rheem, A.O. Smith, Bradford White, State Water Heaters, Navien, Rinnai, Noritz, and Bosch equipment, and we follow Uniform Plumbing Code (UPC) and ANSI Z21.10.1 on every gas appliance we touch. That means the rod we install is the right material and length for your tank, not a universal part that fits nothing well.
- State-licensed plumbing contractor serving Charlotte County and the surrounding ZIP codes.
- We test T&P valves and thermostats on every visit, not just the rod.
- Segmented and solid anode rods both handled, including seized rods on older tanks.
- Powered anode rods installed for homes with recurring sulfur odor problems.
- Work performed to Uniform Plumbing Code (UPC) and ANSI Z21.10.1 standards.
Why Port Charlotte Picks Us for Anode Rod Replacement
We are a local water heater shop, not a general handyman outfit. That focus shows up in how fast we diagnose, how clean we work, and how honestly we tell you when a tank is not worth saving.
Straight Pricing Up Front
You get a price range on the phone and a firm number before we start. Most anode rod replacements in Port Charlotte land between $200 and $400 depending on tank access and rod type. No surprise line items, no pressure to upgrade to a new tank when a rod swap will do.
Same-Day and 24/7 Options
Anode rod replacement Port Charlotte FL 24/7 scheduling is available for active leaks and no-hot-water calls. Standard appointments are usually same day or next morning. If your tank is actively dripping from the rod port, call us and we will move you to the front of the line.
Right Parts on the Truck
We stock magnesium, aluminum, and powered anode rods sized for Rheem, A.O. Smith, Bradford White, and State Water Heaters tanks. That means one trip, not two. If your tank needs a dielectric union or flex connector while we are in there, we have those too.
We Tell You When to Stop
If the tank shell is already rusted through or the leak is coming from the base rather than the fittings, a new rod will not fix it. We will show you the corrosion and quote a replacement instead. Affordable water heater anode rod replacement Port Charlotte makes sense on a sound tank, and we are honest about which tanks qualify.
What Our Anode Rod Service Includes
Every anode rod replacement includes the parts and labor below. If your tank needs something beyond this list, we quote it before we touch anything so there are no surprises on the invoice.
What's Included
New Anode Rod
A magnesium, aluminum, or powered anode rod matched to your tank brand and water chemistry. Magnesium works best in soft water, aluminum in hard water, and powered rods for homes fighting recurring sulfur bacteria. We bring all three and pick the right one on site.
Tank Drain and Flush
We drain the tank and flush out sediment while the rod is out. Port Charlotte water leaves mineral scale behind, and that scale is what causes popping sounds and shortens element life. A flush takes fifteen extra minutes and buys you real runtime.
T&P Valve and Thermostat Check
We test the T&P valve with a tester and verify the thermostat or gas valve is holding temperature correctly. A stuck T&P valve is a safety issue, and a drifting thermostat makes the tank work harder than it should. Both checks are included, not upsold.
Leak Test and Purge
After refill we purge air from every hot tap and watch the rod port for weeping. We check the drain valve, the flex connectors, and the dielectric unions while the tank is pressurized. You get a dry floor and hot water before we pack up.
Written Service Record
You get a note with the rod condition, the replacement date, and the tank model so you know when the next rod is due. Most rods last four to six years in this area. That record also supports any warranty claim with the tank manufacturer.
Problems a Fresh Anode Rod Solves
Most of the calls we get about anode rods start with one of these four complaints. All of them trace back to a depleted rod and the corrosion it allows.
Hot water smells like rotten eggs
Sulfur bacteria colonize a spent magnesium rod and produce hydrogen sulfide gas. The smell gets worse over weeks and makes showers unpleasant. Left alone, the bacteria spread through the tank and the odor returns even after flushing.
We pull the magnesium rod, flush the tank with a chlorine solution, and install an aluminum or powered anode rod. The smell clears the same day in most Port Charlotte homes. If the tank is older, we check the dip tube and heating element while we are in there.
Popping and rumbling from the tank
Sediment builds on the tank floor and traps water underneath, which boils and pops against the burner or element. The noise is annoying, but the real damage is the extra heat stress on the tank lining and the shortened element life.
We drain and flush the tank completely, then replace the anode rod while it is open. Removing the sediment restores even heating and quiets the tank. On electric units we also check the lower heating element for scale damage before we close it up.
Rusty or metallic-tasting hot water
Once the anode rod is gone, the tank lining starts corroding and iron enters your hot water. Rusty water stains laundry and fixtures, and it signals the tank is on borrowed time. Ignoring it usually leads to a leaking tank within a year.
We inspect the tank interior through the rod port with a light. If the corrosion is surface-level, a new rod plus a flush clears the water. If the shell is pitted, we show you and quote a replacement instead of charging for a rod that will not help.
T&P valve weeping or dripping
A failing T&P valve or a waterlogged expansion tank raises system pressure and pushes water out the relief line. That drip can damage the drain pan and the floor beneath the heater. It is also a sign the tank is running hotter than it should.
We test the T&P valve, check the expansion tank charge, and verify the thermostat setting. If the valve is stuck or the expansion tank is shot, we quote that repair alongside the rod replacement. Fixing both at once saves a second service call.
When Anode Rod Replacement Makes Sense
A six-year-old builder-grade tank in Deep Creek that still heats fine but smells like sulfur.
We flush the tank, swap the magnesium rod for an aluminum one, and sanitize the interior. The tank stays in service and the odor goes away. We leave a note with the replacement date so the next rod is due in about five years.
Hot water smells clean again, and the homeowner avoids a $1,400 tank replacement for several more years.
A landlord with a duplex near Murdock who wants to protect two tanks from early failure.
We replace the anode rods in both tanks on the same visit and flush the sediment out. Both tanks get a written service record. Scheduling both together cuts the labor cost per tank.
Two tanks get three to five more years of service, and the owner has documentation for the warranty file.
A homeowner in Harbour Heights whose hot water has turned brown and who is worried the tank is failing.
We pull the rod, inspect the tank lining with a light, and find surface corrosion but no pitting. A new rod and a full flush restore clear hot water. We check the heating element and T&P valve while the tank is open.
Clear hot water within hours, and a clear answer on how much life the tank has left.
A snowbird in Punta Gorda Isles returning for the season who has not serviced the tank in years.
We do a full maintenance visit: drain and flush, rod replacement, T&P valve test, thermostat check, and a look at the expansion tank. Anything marginal gets flagged before it becomes an emergency.
The tank is ready for the season, and the owner knows exactly what condition it is in.
Tools and Methods We Use
Tools & Equipment
Pipe Wrench and Cheater Bar
Used to break the anode rod loose from the tank port. Older rods seize in place, and steady leverage beats impact tools that can crack the fitting.
Tube Cutter and Press Tool
For segmented anode rods and for cutting and re-making copper or PEX lines when the tank has to move slightly for access.
T&P Valve Tester
Verifies the temperature and pressure relief valve opens at the correct setpoint. A stuck valve is a safety problem, not a nuisance.
Multimeter
Checks continuity and voltage on electric tanks, confirms the heating element and thermostat are working, and rules out a circuit board fault.
Water Heater Dolly
Moves a full or partially drained tank safely when the rod port is inaccessible and the unit has to be shifted out of a closet or pan.
Soldering Torch
Used when a flex connector or dielectric union has to be replaced during the job. We sweat the joint, pressure test it, and check for weeping before refill.
Methods & Techniques
Uniform Plumbing Code (UPC) Compliance
Every rod replacement, T&P valve test, and drain pan check follows UPC requirements. That includes proper relief valve sizing, correct drain line termination, and safe gas connections on gas-fired tanks. We pull a Charlotte County Permit when the scope requires one.
ANSI Z21.10.1 Gas Appliance Standard
Gas water heaters are checked against ANSI Z21.10.1 for venting, combustion air, and gas valve function. If the flue or the gas valve is out of spec, we flag it before we return the unit to service.
NFPA 54 Fuel Gas Code
Gas piping and connections are verified against NFPA 54. That means correct sediment trap placement, proper shutoff access, and no unapproved flex connectors on the gas side. It is a quick check that prevents a serious problem.
Powered Anode Conversion
For homes with recurring sulfur odor, we install a powered anode rod that uses a small current to protect the tank without the magnesium reaction. It costs more up front but ends the odor cycle and lasts far longer than a sacrificial rod.
How Anode Rod Replacement Runs in Port Charlotte
Service Areas
Mostly 1990s and early 2000s construction with garage-mounted tanks. Access is easy, and most jobs finish in about 90 minutes.
Many seasonal homes where tanks sit unused for months. We check for stale water, sulfur odor, and a waterlogged expansion tank on every visit.
Older homes with original plumbing and gate valves. We often replace a flex connector or dielectric union while the tank is open.
A mix of rentals and owner-occupied homes. Landlords here frequently schedule two or three tanks on the same visit to save on labor.
Local Considerations
Hard water with high dissolved mineral content
Accelerates anode rod consumption and sediment buildup. Rods here often fail by year five instead of the seven to eight years seen in softer water regions.
Year-round heat and heavy water use
Tanks run more hours per year than in cooler climates, which speeds corrosion and shortens element and rod life. Maintenance intervals should be tighter.
Seasonal occupancy in coastal neighborhoods
Tanks that sit idle for months develop sulfur bacteria and stale water. A flush and rod check at the start of season prevents surprises.
Garage and exterior closet installations
Easier access means faster jobs, but also more exposure to humid air. We check the tank base and fittings for corrosion on every visit.
Sulfur Smell Gone in One Visit
A homeowner in Deep Creek had hot water that smelled like rotten eggs for two months. The tank was six years old and had never been serviced. The magnesium anode rod was almost completely consumed, and the tank floor had a half-inch of sediment.
We flushed the tank, sanitized it, and installed an aluminum anode rod. The odor was gone by the next morning. The tank is still in service and the homeowner avoided a replacement that would have run $1,400 or more.
Maintenance & Follow-up
Check the new rod in four years. Flush the tank annually to keep sediment from rebuilding on the tank floor.
A family in Harbour Heights noticed brown hot water and assumed the tank was finished. The tank was eight years old and the rod was gone, but the shell showed only surface corrosion. The T&P valve was also weeping slightly.
We replaced the rod, flushed the tank, and swapped the T&P valve. Hot water ran clear within an hour. The tank passed a pressure test and is still running today, saving the family a full replacement.
Maintenance & Follow-up
Replace the rod every four to five years and test the T&P valve annually. Watch for any return of discoloration.
A landlord near Murdock had two identical gas tanks, both seven years old, both with original rods. Neither was leaking yet, but the tenant in one unit had complained about popping noises and slow recovery.
We replaced both anode rods and flushed both tanks in a single visit. The popping stopped, recovery time improved, and both tanks got a written service record. The owner saved on labor by bundling the jobs.
Maintenance & Follow-up
Schedule the next rod replacement in four years. Keep the service records with the warranty paperwork for each tank.
What Anode Rod Replacement Costs
Typical 2026 pricing for anode rod replacement in Port Charlotte runs $200 to $400 for a standard tank, including the rod, the flush, and the labor. Powered anode conversions run higher, usually $450 to $700, because the rod itself costs more. Tank access is the biggest variable. A garage-mounted tank with clear headroom is a straightforward job. A tank wedged in an interior closet may need to be shifted on a dolly, which adds time. If we find a failed T&P valve, a bad expansion tank, or a leaking flex connector while the tank is open, we quote that repair before doing it. You always know the number before we start.
Pricing Factors
Tank Location and Access
Garage and exterior closet tanks are quick. Interior closets with low clearance or a tank sitting in a drain pan may require shifting the unit, which adds 20 to 40 minutes of labor.
Rod Type
Standard magnesium and aluminum rods are the least expensive. Powered anode rods cost more because of the rod and the small control module, but they last far longer and end recurring sulfur odor.
Seized or Segmented Rods
Older rods can be seized in the port or come in segments that must be removed in pieces. Both take extra time and sometimes a tube cutter, which affects the final price.
Related Repairs Found
A weeping T&P valve, a waterlogged expansion tank, or a corroded flex connector are common finds. Fixing them during the same visit costs less than a second service call.
Gas vs Electric Tank
Electric tanks are usually simpler because there is no flue or gas valve to check. Gas tanks require combustion and venting verification, which adds a few minutes to the job.
Typical Investment Range
$200 - $700 depending on rod type, tank access, and any related repairs
Actual pricing varies based on project scope and requirements
Value You Receive
A $300 rod replacement that buys three to five more years from a $1,400 tank is the best return in water heater maintenance. It is also the difference between a planned service call and an emergency replacement on a weekend.
Frequently Asked Questions
Have questions? We have answers. If you don't see your question here, feel free to contact us.
Call UsHow much does water heater anode rod replacement cost in Port Charlotte FL?
Most jobs run $200 to $400 for a standard tank, including the rod, the flush, and labor. Powered anode conversions run $450 to $700. Tank access, rod type, and any related repairs found during the visit are the main variables. We give you a firm number before we start, and we never quote a rod swap on a tank that is already rusted through.
How often should a water heater anode rod be replaced in Port Charlotte?
Every four to six years in this area. Port Charlotte water is hard, and the year-round heat speeds up rod consumption. Builder-grade tanks from the 1990s and 2000s often need a rod by year five. If your hot water smells like sulfur or the tank is popping, check the rod now rather than waiting for the calendar.
Who replaces water heater anode rods near me in Port Charlotte?
We do. Port Charlotte Water Heater Pros handles anode rod replacement across Charlotte County, including Deep Creek, Murdock, Harbour Heights, and Punta Gorda Isles. We stock magnesium, aluminum, and powered rods for Rheem, A.O. Smith, Bradford White, and State Water Heaters tanks. Call (941) 466-8418 and we will schedule a same-day or next-morning visit.
How long does water heater anode rod replacement take in Port Charlotte?
Plan on 90 minutes to two hours for a standard tank. That includes draining, removing the old rod, flushing sediment, installing the new rod, refilling, and testing. A seized rod or a tight closet install can add 30 to 45 minutes. We confirm the time window when you book and call ahead before we arrive.
Licensed, Insured, and Local
Certifications
Customer Reviews
Called about a sulfur smell in our hot water. They came out the next morning, flushed the tank, and swapped the anode rod. The smell was gone that night. Fair price and they explained everything they found. We are in Deep Creek and will use them again.
Our tank was eight years old and the water was rusty. They pulled the rod, checked the tank, and told us honestly it was worth saving. New rod, flush, and a new T&P valve. Hot water runs clear now. Saved us a full replacement.
We manage a couple of rentals near Murdock and had them do both tanks in one visit. They were on time, cleaned up, and left a written record for each tank. Bundling the jobs saved us money and the tenants stopped complaining about the popping noise.
Related Services
Explore our other professional services
Tankless Water Heater Installation
If your tank is past saving, a tankless unit frees up floor space and never runs out of hot water. We size Navien, Rinnai, and Noritz units for Port Charlotte homes and handle the gas and venting work.
Tankless Water Heater InstallationTank Water Heater Installation
When a rod swap will not save the tank, we install Rheem, A.O. Smith, and Bradford White tanks sized for your household. We haul the old unit away and bring the new one up to code.
Tank Water Heater InstallationEmergency Water Heater Replacement
A tank that fails at 10 p.m. does not wait for business hours. We handle emergency replacements across Port Charlotte, including nights and weekends, and get hot water back the same day when possible.
Emergency Water Heater ReplacementSame-Day Water Heater Replacement
If your tank is leaking from the shell and a rod will not help, we can often replace it the same day. We stock common sizes on the truck and confirm availability when you call.
Same-Day Water Heater ReplacementGas Water Heater Replacement
Gas tanks need proper venting and combustion air. We replace gas units to NFPA 54 and ANSI Z21.10.1 standards and test the gas valve and flue before we leave.
Gas Water Heater ReplacementElectric Water Heater Replacement
Electric replacements are usually the fastest swap we do. We check the circuit, the breaker, and the heating elements, and we verify the thermostat is set correctly before we close up.
Electric Water Heater ReplacementHybrid Heat Pump Water Heater Installation
Heat pump water heaters cut energy use significantly in Florida's warm climate. We handle sizing, condensate drainage, and the electrical work for a clean install.
Hybrid Heat Pump Water Heater InstallationSolar Water Heater Installation
Solar water heating pairs well with a healthy tank and a fresh anode rod. We install and service solar systems and make sure the backup element is working for cloudy weeks.
Solar Water Heater InstallationCondensing Water Heater Installation
Condensing units reach efficiency ratings above 90 percent. We install them with the correct PVC venting and condensate management for Port Charlotte homes.
Condensing Water Heater InstallationPower Vent Water Heater Installation
Power vent tanks solve venting problems in homes without a chimney. We install them with the correct blower and vent termination and test the pressure switch before startup.
Power Vent Water Heater InstallationDirect Vent Water Heater Installation
Direct vent units pull combustion air from outside, which is ideal for tight closets. We install and seal the vent kit and verify the unit meets code clearances.
Direct Vent Water Heater InstallationHigh-Efficiency Water Heater Upgrade
Upgrading from a standard tank to a high-efficiency model lowers monthly gas or electric bills. We walk you through the payback period and handle the install and permits.
High-Efficiency Water Heater UpgradeWater Heater Tank Removal & Disposal
When a tank is done, we drain it, disconnect it, and haul it away. We recycle the steel and dispose of the old unit properly so you are not stuck with it in the garage.
Water Heater Tank Removal & DisposalWater Heater Code Compliance Upgrades
Older installs often lack a drain pan, a proper T&P discharge line, or a sediment trap. We bring them up to Uniform Plumbing Code standards and pull a Charlotte County Permit when needed.
Water Heater Code Compliance UpgradesWater Heater Expansion Tank Installation
A waterlogged or missing expansion tank raises system pressure and shortens tank life. We install and charge new expansion tanks to match your water pressure.
Water Heater Expansion Tank InstallationWater Heater Pan Installation
A drain pan with a routed discharge line protects your floor and drywall when a tank weeps. We install pans on new and existing tanks and route the drain to a safe location.
Water Heater Pan InstallationWater Heater Drain Pan Replacement
Cracked or rusted pans leak instead of containing water. We swap them out and re-route the drain line so a future drip goes where it should.
Water Heater Drain Pan ReplacementWater Heater Sediment Flush & Maintenance
Annual flushing removes the scale that causes popping and shortens element life. Pair it with a rod check and you get the most life out of your tank.
Water Heater Sediment Flush & MaintenanceWater Heater Thermostat Replacement
A drifting thermostat makes the tank run hot or run cold. We test and replace thermostats on gas and electric tanks and verify the temperature at the tap.
Water Heater Thermostat ReplacementWater Heater Heating Element Replacement
Scale buildup burns out heating elements. We replace upper and lower elements, check the thermostat, and flush the tank so the new element lasts.
Water Heater Heating Element ReplacementWater Heater T&P Valve Replacement
A stuck or weeping T&P valve is a safety issue. We replace it with the correctly rated valve and verify the discharge line terminates properly.
Water Heater T&P Valve ReplacementWater Heater Gas Valve Replacement
A failing gas valve causes no heat, weak flame, or a pilot that will not stay lit. We replace it, check the thermocouple and igniter, and test for leaks.
Water Heater Gas Valve ReplacementWater Heater Igniter Replacement
On demand and power vent units, a bad igniter means no hot water. We test the ignition sequence and replace the igniter so the burner lights reliably.
Water Heater Igniter ReplacementWater Heater Thermocouple Replacement
A thermocouple that reads wrong shuts the gas off. We replace it, verify the pilot holds, and check the gas valve while we are in there.
Water Heater Thermocouple ReplacementWater Heater Pilot Light Repair
A pilot that keeps going out usually means a dirty orifice, a bad thermocouple, or a draft issue. We diagnose it and fix the root cause, not just relight it.
Water Heater Pilot Light RepairWater Heater Leak Repair
Not every leak means a new tank. Fittings, drain valves, and T&P valves can all weep. We find the source and repair it when the tank shell is still sound.
Water Heater Leak RepairWater Heater Pressure Relief Valve Repair
Pressure problems often trace back to a waterlogged expansion tank or high street pressure. We test the system and fix the cause, not just the valve.
Water Heater Pressure Relief Valve RepairWater Heater Circuit Board Repair
Modern tanks rely on control boards for ignition and temperature control. We diagnose board faults and replace them when repair is not possible.
Water Heater Circuit Board RepairWhat Port Charlotte Customers Say
Real experiences from customers who chose our Water Heater Anode Rod Replacement services
"Our hot water smelled like rotten eggs for weeks. Port Charlotte Water Heater Pros came out, flushed the tank, and put in an aluminum anode rod. The smell was gone by that evening. They also checked the T&P valve and the heating element while they were in there. Honest pricing and no push to buy a new tank."
Dana R.
Homeowner, Deep Creek
"I had two rental tanks that both needed anode rods. They did both in one visit and left a written record for each. The popping noise the tenant complained about stopped right away. Scheduling both together saved me on labor, and they were in and out in about three hours total."
Marcus T.
Landlord, Murdock
"We thought our eight-year-old tank was done because the hot water was brown. They pulled the rod, looked inside with a light, and said the shell was still good. New rod and a flush and the water ran clear. That was two years ago and the tank is still going strong."
Ellen K.
Homeowner, Harbour Heights
Book Water Heater Anode Rod Replacement Port Charlotte FL
One visit, one price, and a tank that lasts years longer. We are licensed, local to Charlotte County, and we stock the right rod for your brand. Call (941) 466-8418 and we will get you on the schedule, often the same day.