Water Heater Igniter Replacement Port Charlotte FL You Can Count On
Fast, licensed igniter service for gas and tankless water heaters
When your gas water heater clicks but never lights, you need water heater igniter replacement Port Charlotte FL homeowners trust. We diagnose the igniter, test the gas valve and flame sensor, and restore reliable ignition, usually the same day. Whether you own a Rheem, A.O. Smith, or Navien unit in Charlotte County, our licensed team gets your hot water back without the guesswork.
Water Heater Igniter Replacement Port Charlotte FL Explained
Water heater igniter replacement Port Charlotte FL is the repair that swaps a failed ignition component so your gas water heater lights reliably again. The igniter, sometimes called a hot surface igniter or spark electrode, creates the heat or spark that lights the burner. When it cracks, carbon-fouls, or loses resistance, the burner never fires and you get cold water. We test the igniter with a multimeter, confirm the gas valve and flame sensor are working, then install a manufacturer-matched replacement.
Port Charlotte sits in a humid, salt-air climate that accelerates corrosion on igniter contacts and wiring harnesses. Add hard water that leaves sediment buildup in the tank, and ignition components wear faster than in drier markets. If your heater clicks repeatedly, smells faintly of gas, or shuts off mid-cycle, call us for igniter replacement Port Charlotte FL 24/7. We stock igniters for Rheem, Bradford White, State Water Heaters, and Bosch models common in local homes.
Why Port Charlotte Homeowners Choose Our Igniter Service
A failed igniter leaves you without hot water and can mask a bigger gas valve or circuit board problem. Here is what our igniter replacement in Port Charlotte delivers for local homeowners.
Hot Water Restored Fast
Most igniter replacements take two to four hours from arrival to first successful light-off. We carry igniters for Rheem, A.O. Smith, and Navien units on the truck, so you are not waiting days for a part order. You get a tested, firing water heater before we leave your driveway.
Licensed Gas Work Only
Igniter replacement touches the gas train, so it falls under the Uniform Plumbing Code (UPC) and NFPA 54. Our technicians hold a Florida Plumbing License and pull a Charlotte County Permit when the scope requires it. That protects your home, your insurance, and your warranty.
Diagnosis Before Parts
We test the igniter, gas valve, flame sensor, and thermostat with a multimeter before quoting a repair. A clicking heater is not always a bad igniter. Sometimes it is a gas valve failure or a dirty flame sensor. You pay for the fix that actually solves the problem.
Affordable, Upfront Pricing
Affordable water heater igniter replacement Port Charlotte starts with a clear price before we open a panel. Typical 2026 igniter jobs run $180 to $450 depending on the model and access. No surprise line items, no pressure to replace a heater that only needs one part.
Our Igniter Replacement Process
We keep the process simple and transparent. Here is exactly what happens from your first call to the moment your burner lights again.
Phone Diagnosis
You describe the symptoms: clicking, no hot water, error code, or a faint gas smell. We ask for your heater brand and model, then book a window that fits your day. Most Port Charlotte calls get a same-day or next-morning slot.
On-Site Testing
Our technician shuts off gas, opens the burner compartment, and tests the igniter with a multimeter. We check resistance against the manufacturer spec, inspect the flame sensor, and confirm the gas valve opens. This takes about 20 minutes and tells us exactly what failed.
Part Match and Install
We pull the correct igniter for your Rheem, Bradford White, or State Water Heaters model from the truck. The old igniter comes out, the new one goes in with a clean connection, and we torque the burner assembly to spec. Installation runs 30 to 60 minutes.
Light-Off and Safety Check
We restore gas, cycle the heater, and watch the burner light through at least two full cycles. A T&P valve tester and combustion check confirm safe operation. If we spot a leaking tank or a bad expansion tank, we tell you before we leave.
Walkthrough and Warranty
You get a plain-English rundown of what failed, what we replaced, and how to keep it working. Our workmanship warranty covers the install, and the part carries its manufacturer warranty. We leave the work area as clean as we found it.
Local Igniter Expertise You Can Verify
Our technicians work on gas water heaters every week, not once a season. We hold a Florida Plumbing License and follow the Uniform Plumbing Code (UPC), ANSI Z21.10.1, and NFPA 54 on every job. That means igniter replacement done to code, with gas connections tested and combustion verified. We service Rheem, A.O. Smith, Navien, Rinnai, Bradford White, State Water Heaters, Noritz, and Bosch units across Charlotte County. When a heater needs more than an igniter, we can move straight into thermostat, gas valve, or heating element work without sending you to another contractor.
- Licensed Florida plumbing contractor with gas water heater specialization
- Code-compliant work under UPC, ANSI Z21.10.1, and NFPA 54
- Weekly igniter and gas valve diagnostics on Rheem, Navien, and Bradford White units
- Multimeter testing on every igniter before we recommend replacement
- Charlotte County Permit handling when the scope requires inspection
Why Our Water Heater Igniter Replacement Port Charlotte FL Stands Out
Plenty of companies will swap an igniter. Fewer will test the whole ignition circuit, explain what failed, and stand behind the repair. Here is what sets our team apart.
Same-Day Availability
We hold same-day water heater igniter replacement Port Charlotte slots open for no-hot-water calls. Call before noon and there is a strong chance a technician is at your door that afternoon. We stock common igniters so the job finishes in one visit, not two.
Full Ignition Circuit Testing
A new igniter will not fix a bad gas valve or a corroded flame sensor. We test the entire ignition path, including the circuit board on electronic models, before quoting. That is how we avoid callbacks and how you avoid paying twice for the same symptom.
Parts for Every Major Brand
Our trucks carry igniters and ignition components for Rheem, A.O. Smith, Navien, Rinnai, Bradford White, State Water Heaters, Noritz, and Bosch. If your model needs a rare part, we source it fast and schedule the return visit around your availability.
Honest Repair-or-Replace Advice
If your heater is 12 years old with a leaking tank and sediment buildup, an igniter is a bandage. We tell you that plainly. If a $300 igniter repair buys you years of service, we say that too. You get the truth, not the biggest invoice.
What Our Igniter Replacement Service Includes
Every igniter job covers the full ignition circuit, not just the part. Here is what is included when we replace your water heater igniter in Port Charlotte, Florida. Add-on work like thermostat replacement or a sediment flush is quoted separately before we start.
What's Included
Igniter Testing and Replacement
We test the existing igniter with a multimeter, confirm the failure, and install a manufacturer-matched replacement. The burner assembly is torqued to spec and the connection is cleaned so the new igniter lasts.
Gas Valve and Flame Sensor Check
A failed igniter often travels with a dirty flame sensor or a sticking gas valve. We inspect and test both so the burner lights and stays lit through full cycles, not just on the first try.
Burner Compartment Cleanout
Dust, rust flakes, and insect debris collect in the burner compartment. We vacuum it out before installing the new igniter, which protects the part and improves combustion on your Rheem or A.O. Smith unit.
Light-Off and Combustion Verification
After reassembly, we cycle the heater at least twice and confirm a steady flame. We check for gas leaks at every connection we touched and verify the T&P valve is not weeping before we pack up.
Workmanship Warranty
Our install work is warrantied, and the igniter carries its manufacturer warranty. If the same ignition fault returns within the warranty window, we come back and make it right at no labor charge.
Ignition Problems We Solve in Port Charlotte
Most no-hot-water calls trace back to one of a handful of ignition faults. Here are the ones we see most often on Port Charlotte water heaters and how we fix them.
Heater clicks but never lights
You get cold showers and a heater that runs through its start cycle without firing. Left alone, repeated failed light-offs can flood the burner compartment with unburned gas.
We test the igniter resistance, inspect the flame sensor, and confirm the gas valve opens. In most cases a new igniter restores ignition the same visit. If the gas valve has failed, we quote that repair before touching anything.
Burner lights then shuts off
Short cycling wears the igniter, gas valve, and circuit board. Your hot water turns lukewarm and the heater locks out with an error code.
We test the flame sensor and igniter together, since a weak sensor mimics a bad igniter. Cleaning or replacing the sensor plus a fresh igniter usually ends the lockouts. On Navien and Rinnai tankless units we also check the intake for debris.
Faint gas smell near the heater
Any gas odor near a water heater is a safety issue. It can mean a failed gas valve, a loose connection, or unburned gas from repeated failed ignition.
We shut off the gas, inspect every connection in the burner compartment, and test the gas valve. If the valve failed, we replace it alongside the igniter. We never leave a heater running with an unresolved gas smell.
Error code on an electronic model
Electronic ignition heaters from Rheem, A.O. Smith, and State Water Heaters throw codes that point to ignition, flame sensing, or the circuit board. Guessing at parts gets expensive fast.
We read the code, then test the igniter, flame sensor, and circuit board in sequence. That order matters. It tells us whether you need a $200 igniter or a board repair, and we quote the actual fix.
When to Call for Igniter Replacement
Your gas water heater stopped firing after a summer storm knocked out power in Deep Creek.
We test the igniter and control board, since power surges can damage both. If the igniter cracked, we replace it and verify the board still sends proper voltage. If the board failed, we quote that repair separately.
You get a heater that lights on the first click, usually within the same visit, with both the igniter and board confirmed working.
A tankless Navien unit in Gulf Cove shows an ignition error and shuts down mid-shower.
We open the unit, test the igniter and flame sensor, and check the intake and condensate lines for blockages. Tankless igniters foul faster in humid coastal air, so we clean the assembly and replace the igniter when resistance is out of spec.
Your tankless heater runs through a full shower cycle without locking out, and you get a maintenance note on how often to clean the intake.
You are selling a home near Port Charlotte Town Center and the inspection flagged a water heater that will not light.
We diagnose the ignition fault, replace the igniter if that is the cause, and provide a clear record of the repair. If the heater is at end of life, we document that too so the buyer and seller can negotiate with facts.
The inspection item clears, the closing stays on schedule, and the new owner has a working heater with a documented repair.
Your Bradford White heater in Harbour Heights clicks for 30 seconds before locking out every morning.
We test the igniter, clean the flame sensor, and check the gas valve for slow opening. A weak igniter plus a carbon-fouled sensor is a common pair in humid climates. We replace the igniter and clean the sensor in one visit.
Morning showers go back to normal, and the heater lights within a few seconds instead of cycling to a lockout.
Tools and Methods We Use
Tools & Equipment
Multimeter
Tests igniter resistance, flame sensor microamps, and voltage at the control board. This is how we confirm an igniter has failed before quoting a replacement.
Pipe Wrench and Tube Cutter
Used when we need to break gas connections to reach the burner assembly or replace a gas valve alongside the igniter. Every connection gets leak-tested after reassembly.
T&P Valve Tester
Confirms the temperature and pressure relief valve opens and reseats correctly. A weeping T&P valve is often mistaken for a tank leak during an ignition call.
Water Heater Dolly
Moves a full tank safely when the igniter job turns into a replacement. It protects your floor and our backs, and it keeps the job moving without a second crew.
Soldering Torch and Press Tool
For gas line and water line work around the heater. The press tool lets us make code-compliant connections without an open flame in tight closets.
Methods & Techniques
Uniform Plumbing Code (UPC) gas train protocol
Every gas connection we touch is leak-tested with soap solution or a combustible gas detector. We follow UPC and NFPA 54 for clearances, venting, and combustion air, so the repair passes inspection when a Charlotte County Permit is required.
ANSI Z21.10.1 ignition testing sequence
We test the ignition circuit in the order the standard expects: power at the board, voltage to the igniter, igniter resistance, flame sensing, then gas valve operation. That sequence finds the real fault instead of replacing parts by guesswork.
Manufacturer-matched part sourcing
Igniters are model-specific. We match the part to your Rheem, A.O. Smith, Navien, Rinnai, Bradford White, State Water Heaters, Noritz, or Bosch model rather than forcing a universal part that fails early.
Post-repair combustion verification
After the new igniter is in, we cycle the burner at least twice and watch the flame. A steady flame with no rollout and no lockout is the sign the repair is complete, not just the part swap.
How Igniter Replacement Runs in Port Charlotte
Service Areas
Many homes here run on well water with higher mineral content, which accelerates sediment buildup and shortens igniter and heating element life.
Older gas heaters are common, and original igniters are often past their service life. We stock replacements for the brands installed in this area.
Salt air exposure is stronger near the water, so we see corroded igniter contacts and wiring harnesses more often on these properties.
Condos and townhomes here often have heaters in tight closets, which means careful venting and clearance checks during igniter replacement.
Coastal properties with tankless units need intake cleaning alongside igniter work because humid air and debris foul the burner assembly.
Local Considerations
Year-round coastal humidity
Moisture corrodes igniter terminals and flame sensors, so we clean and dielectric-protect connections during every replacement to extend part life.
Hard water and sediment buildup
Sediment stresses the tank and burner, causing overheating and premature igniter failure. We recommend a sediment flush when buildup is visible.
Older housing stock with original heaters
Many Port Charlotte heaters are 10 to 15 years old. We check the tank, anode rod, and T&P valve during igniter work so you know the real condition.
Seasonal storm power surges
Surges can damage igniters and control boards together. After a storm, we test both so a board fault is not mistaken for a simple igniter failure.
Clicking Rheem Restored in Deep Creek
A Deep Creek homeowner had a Rheem gas heater that clicked for 45 seconds every morning and then locked out. Two prior visits replaced the igniter with a universal part that failed within weeks. The family was taking cold showers and considering a full replacement.
We tested the ignition circuit, found the universal igniter had the wrong resistance, and installed the manufacturer-matched part. The heater now lights in under 5 seconds. Total cost was $310, and the family avoided a $1,800 replacement.
Maintenance & Follow-up
We recommended a sediment flush every 12 months and an annual igniter and flame sensor check to keep the burner compartment clean in this hard-water area.
A Gulf Cove family had a Navien tankless unit throwing an ignition error mid-shower. The unit had never been serviced, and the intake was packed with debris and salt-air corrosion on the igniter assembly.
We cleaned the intake and burner assembly, replaced the fouled igniter, and tested through three full draw cycles. The unit now runs a 20-minute shower without a lockout. The repair came in at $395.
Maintenance & Follow-up
We set them up on annual tankless descaling and intake cleaning, which is the single best way to protect the igniter in coastal humidity.
A homeowner near Port Charlotte Town Center was told by another company that their 9-year-old Bradford White heater needed full replacement. The symptom was a heater that would not light, and the quote was $2,200.
We tested the igniter and gas valve and found only the igniter had failed. A $275 replacement restored hot water the same day. The tank, anode rod, and T&P valve all checked out fine for continued service.
Maintenance & Follow-up
We suggested checking the anode rod annually and flushing sediment once a year, which should carry this heater several more years before replacement makes sense.
Water Heater Igniter Replacement Cost
Typical 2026 pricing for water heater igniter replacement in Port Charlotte runs $180 to $450, depending on the model, part cost, and how hard the burner compartment is to reach. Tankless igniters and electronic models often sit at the higher end because diagnosis takes longer. We quote the full job before we start, so you know the number before we open a panel. If the diagnosis points to a gas valve or circuit board instead, we tell you and re-quote rather than padding the igniter bill.
Pricing Factors
Heater type and brand
Tankless igniters for Navien, Rinnai, and Noritz units cost more than standard tank igniters for Rheem or A.O. Smith. Part availability also affects the price when a rare model needs a special order.
Access to the burner
Heaters in tight closets or behind finished walls take longer to reach. We may need to move a water heater dolly into place or disconnect a flex connector to get clear access, which adds labor time.
Related failed components
If the flame sensor is fouled or the gas valve has failed, that work is quoted alongside the igniter. Fixing both in one visit is cheaper than two separate service calls.
Permit requirements
Some gas train repairs require a Charlotte County Permit and inspection. When that applies, the permit fee is part of the quote, and we handle the paperwork and the inspection scheduling.
After-hours or emergency calls
Igniter replacement Port Charlotte FL 24/7 emergency calls carry a higher rate than standard business hours. If you can wait for a morning slot, you will pay less for the same repair.
Typical Investment Range
$180 - $450 depending on model, access, and related parts
Actual pricing varies based on project scope and requirements
Value You Receive
An igniter repair at this price keeps a working heater in service instead of forcing a $1,500 to $2,500 replacement. When the rest of the unit checks out, it is the highest-value fix on the menu.
Frequently Asked Questions
Have questions? We have answers. If you don't see your question here, feel free to contact us.
Call UsHow much does water heater igniter replacement cost in Port Charlotte FL?
Most igniter replacements in Port Charlotte run $180 to $450 in 2026, including the part and labor. Tankless models and heaters in tight closets sit at the higher end. If we find a failed gas valve or flame sensor during testing, we quote that work before starting it, so the final bill matches what we told you.
How do I know if my water heater igniter is bad in Port Charlotte?
The clearest sign is a heater that clicks repeatedly but never lights. You may also see a lockout code on electronic models or smell a faint gas odor from failed light-offs. A multimeter test confirms it. We check igniter resistance against the manufacturer spec before recommending replacement, because a dirty flame sensor can mimic the same symptoms.
Who replaces water heater igniters near me in Port Charlotte?
Port Charlotte Water Heater Pros handles igniter replacement across Charlotte County, including Deep Creek, Harbour Heights, Gulf Cove, and Punta Gorda Isles. We are a licensed Florida plumbing contractor, we stock igniters for Rheem, A.O. Smith, Navien, Bradford White, and State Water Heaters, and we follow UPC and NFPA 54 on every gas connection.
How long does water heater igniter replacement take in Port Charlotte?
Most igniter replacements take two to four hours from arrival to final light-off. The part swap itself is 30 to 60 minutes. The rest is diagnosis, burner compartment cleaning, and cycling the heater twice to confirm a steady flame. Tankless units can take longer if the intake or condensate lines need cleaning at the same time.
Licensed and Accountable
Certifications
Customer Reviews
Our Rheem heater clicked for weeks and another company wanted to replace the whole unit. Port Charlotte Water Heater Pros tested the igniter, found the real problem, and had hot water back the same afternoon. The price was exactly what they quoted on the phone.
Navien tankless unit kept throwing an ignition error. They cleaned the intake, replaced the igniter, and walked me through the annual maintenance. No upselling, just the repair I needed. Highly recommend for anyone in the Gulf Cove area.
Called about a Bradford White that would not light. Technician arrived on time, tested everything with a multimeter, and explained what failed. New igniter installed and the burner fired right up. Clean work and a fair price.
Same-day service in Deep Creek when our gas heater died. They diagnosed a bad igniter and a dirty flame sensor, fixed both, and tested the T&P valve while they were there. Professional, licensed, and honest about what the heater needed.
Related Services
Explore our other professional services
Tankless Water Heater Installation
If your tankless igniter keeps failing on an aging unit, a new high-efficiency install may cost less over five years. We size the unit for your Port Charlotte home and handle venting and gas line upgrades.
Tankless Water Heater InstallationTank Water Heater Installation
When a heater is past 12 years and the tank is leaking, igniter repair is a bandage. We install Rheem, A.O. Smith, and Bradford White tanks with new expansion tanks and drain pans.
Tank Water Heater InstallationEmergency Water Heater Replacement
If your heater fails on a weekend or holiday, our emergency replacement service gets a new unit in fast. We handle the old tank removal and disposal in the same visit.
Emergency Water Heater ReplacementSame-Day Water Heater Replacement
Call before noon and we can often replace a failed heater the same day. We stock common sizes and brands, so you are not waiting on a warehouse order.
Same-Day Water Heater ReplacementGas Water Heater Replacement
Gas heaters are what we work on most. When ignition problems point to a failing unit, we replace it with a correctly sized model and verify combustion and venting to code.
Gas Water Heater ReplacementElectric Water Heater Replacement
Electric units have no igniter, but they fail in their own ways. We replace electric heaters and test the heating element, thermostat, and circuit board before we leave.
Electric Water Heater ReplacementHybrid Heat Pump Water Heater Installation
Heat pump water heaters cut energy bills in Florida's warm climate. We install and commission hybrid units, including condensate management and correct clearances.
Hybrid Heat Pump Water Heater InstallationSolar Water Heater Installation
Solar water heating pairs well with Port Charlotte's sun exposure. We install and service solar systems, including backup electric elements and controller setup.
Solar Water Heater InstallationCondensing Water Heater Installation
Condensing units reach higher efficiency but need proper condensate drainage. We install them with correct venting and neutralization for long service life.
Condensing Water Heater InstallationPower Vent Water Heater Installation
Power vent heaters solve venting problems in homes without a chimney. We install them with correct PVC venting and confirm the blower and pressure switch operate.
Power Vent Water Heater InstallationDirect Vent Water Heater Installation
Direct vent units pull combustion air from outside, which suits tight Port Charlotte closets. We install them with correct clearances and sealed vent terminations.
Direct Vent Water Heater InstallationHigh-Efficiency Water Heater Upgrade
Upgrading from a standard tank to a high-efficiency model cuts standby losses. We handle sizing, venting, and any gas line or electrical upgrades the new unit needs.
High-Efficiency Water Heater UpgradeWater Heater Tank Removal & Disposal
Old tanks are heavy and awkward. We drain, disconnect, and haul away your old unit, then recycle the metal and dispose of components properly.
Water Heater Tank Removal & DisposalWater Heater Code Compliance Upgrades
Older installs often miss current UPC and NFPA 54 requirements. We bring expansion tanks, drain pans, and venting up to code so inspections pass.
Water Heater Code Compliance UpgradesWater Heater Expansion Tank Installation
A failed expansion tank stresses the whole system and can cause T&P valve leaks. We install correctly sized tanks and set the pre-charge pressure to match your supply.
Water Heater Expansion Tank InstallationWater Heater Pan Installation
A drain pan with a routed drain line protects your floors from tank leaks. We install pans in attics, closets, and garages and connect them to a safe discharge point.
Water Heater Pan InstallationWater Heater Drain Pan Replacement
Cracked or rusted pans leak instead of protecting. We replace them, check the drain line for clogs, and confirm water actually reaches the outside.
Water Heater Drain Pan ReplacementWater Heater Sediment Flush & Maintenance
Sediment buildup shortens igniter and element life. Our annual flush removes mineral scale and keeps the burner and tank running cooler.
Water Heater Sediment Flush & MaintenanceWater Heater Anode Rod Replacement
The anode rod sacrifices itself to protect the tank. We inspect and replace it before the tank starts corroding, which extends heater life by years.
Water Heater Anode Rod ReplacementWater Heater Thermostat Replacement
A failed thermostat causes temperature swings or no heat at all. We test and replace thermostats on gas and electric models and verify the new setting.
Water Heater Thermostat ReplacementWater Heater Heating Element Replacement
Electric heaters lose hot water when an element burns out. We test both elements, replace the failed one, and check the thermostat while we are in the tank.
Water Heater Heating Element ReplacementWater Heater T&P Valve Replacement
A weeping T&P valve signals excess pressure or a failed valve. We test and replace it, then check the expansion tank and supply pressure for the root cause.
Water Heater T&P Valve ReplacementWater Heater Gas Valve Replacement
When the gas valve fails, the burner never lights no matter how good the igniter is. We replace valves on major brands and leak-test every connection.
Water Heater Gas Valve ReplacementWater Heater Thermocouple Replacement
On standing-pilot heaters, a failed thermocouple shuts the pilot off. We replace it, verify the pilot holds, and check the burner for clean combustion.
Water Heater Thermocouple ReplacementWater Heater Pilot Light Repair
A pilot that will not stay lit usually means a thermocouple, gas valve, or draft problem. We diagnose the cause and repair it rather than relighting it repeatedly.
Water Heater Pilot Light RepairWater Heater Leak Repair
Leaks at fittings, the T&P valve, or the drain valve are often fixable. We locate the source, repair it, and tell you honestly if the tank itself is failing.
Water Heater Leak RepairWater Heater Pressure Relief Valve Repair
A dripping relief valve points to thermal expansion or a bad valve. We test it, replace it when needed, and address the pressure issue behind it.
Water Heater Pressure Relief Valve RepairWater Heater Circuit Board Repair
Electronic heaters depend on the control board for ignition timing. When the board fails, we diagnose it and repair or replace it so the igniter gets proper voltage.
Water Heater Circuit Board RepairWhat Port Charlotte Customers Say
Real experiences from customers who chose our Water Heater Igniter Replacement services
"Our gas heater clicked every morning and then quit. Two other companies told us to replace it. These guys tested the igniter with a multimeter, showed me the bad part, and had it swapped in under an hour. Hot water was back the same day and the bill was $290. Straightforward and honest."
Mark R.
Homeowner, Deep Creek
"The Navien tankless unit kept shutting off mid-shower with an ignition error. They cleaned the intake, replaced the fouled igniter, and ran it through three cycles to prove it was fixed. They also showed me how to keep the intake clear. No more cold showers, and no pressure to buy a new unit."
Sandra L.
Homeowner, Gulf Cove
"I manage several rentals and use Port Charlotte Water Heater Pros for igniter and gas valve work. They show up when they say, test the whole ignition circuit instead of guessing, and leave a clear record of the repair. That reliability is why I keep calling them for every unit in the area."
Dennis P.
Property Manager, Port Charlotte Town Center
Get Your Water Heater Igniter Replacement Port Charlotte FL Today
No hot water is not something to wait on. Our licensed team tests the ignition circuit, replaces the failed igniter, and confirms a steady flame before we leave. Call now and we will get you on the schedule, often the same day.